Build #2: StewMac Mahogany Dreadnought
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
Trimming the edges of the top and back
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
After sanding but before cutting the channels for the binding.
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
I had Kathy Matsushita help me with cutting the channels for the purfling, binding, and the end wedge.
Fortunately the dark spot on the top bass shoulder will get removed by the purfling channel Fitting a plug in the neck slot so the router can flow over that spot
Fortunately the dark spot on the top bass shoulder will get removed by the purfling channel Fitting a plug in the neck slot so the router can flow over that spot
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
Using Kathy's setup to cut the channels
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
Checking the fit
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
Cutting the end wedge
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
First look at the purfling as the tape is coming off
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
First time using a bending iron
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 363
- Joined: Wed Jul 29, 2015 9:04 pm
- Location: San Jose, CA, USA
Re: Build #2: StewMac Mahogany Dreadnought
I'm trying a set of bindings wrapped in aluminum foil to try and reduce scorching. I'm then fitting the bent pieces into the form. They will stay there until next week when I can work on the instrument again.
You do not have the required permissions to view the files attached to this post.
- Randall Newcomb
10 fingers in, 10 fingers out - another good day in the shop
10 fingers in, 10 fingers out - another good day in the shop
-
- Posts: 7
- Joined: Sat Jan 21, 2012 9:14 pm
- Location: San Jose, CA
- Contact:
Re: Build #2: StewMac Mahogany Dreadnought
I think maybe using the foil was what allowed it to scorch; the foil is just tranferring the heat, just as the metal bending iron is. Putting a damp piece of cloth on the bending iron as you bend would probably have kept it from scorching (and would provide more steam, also) -- maybe you didn't get my email where I had mentioned this? :)rcnewcomb wrote:I'm trying a set of bindings wrapped in aluminum foil to try and reduce scorching.