Band Saw - Bench top versus floor

Storebought or Homemade: Tell Us!
Post Reply
PSmill
Posts: 111
Joined: Sun Sep 09, 2018 12:23 pm
Location: British Columbia, Canada

Band Saw - Bench top versus floor

Post by PSmill »

Hi, I'm considering a next build, maybe from scratch or partially from scratch. A band saw would pretty well round out my shop for power tools. Wondering what size people are using for doing necks etc., any pros, cons, minimum capacity to look for, or other thoughts? Tnx.
Danl8
Posts: 733
Joined: Mon Jul 28, 2014 7:50 am
Location: Chadds Ford, PA

Re: Band Saw - Bench top versus floor

Post by Danl8 »

I have both a bench top and a standing 14" Jet. For little tasks the bench top works fine. The Jet with riser block is sort of a minimally acceptable size & quality for re-sawing. I don't do a lot of that, but I think it is overall more useful. Blade selection and guides, and set-up/tuning are the key aspects of getting good cuts. (IMHO)
Kevin Sjostrand
Posts: 3712
Joined: Sat Feb 09, 2008 8:06 pm
Location: Visalia, CA

Re: Band Saw - Bench top versus floor

Post by Kevin Sjostrand »

I agree with Dan. I have both a floor standing 14" resaw bandsaw and a table top Craftsman 10". Of course the big saw will do everything you can think of, but the smaller saw can work for neck work, cutting out tops, backs and sides, etc. The most important thing is the right blade for the task, and a quality blade.
A small saw with a 1/4" blade will resaw, but you will be limited to about 4" of height.
ruby@magpage.com
Posts: 1564
Joined: Thu May 24, 2012 8:03 am
Location: Chestertown Maryland

Re: Band Saw - Bench top versus floor

Post by ruby@magpage.com »

The small cheap ones, especially those with 3 wheels, can be notoriously hard to keep adjusted. Very easy to come up with a used 14" in the Delta style for $350 and would be my recommendation as a first saw so you don't get frustrated with it. I have a 50 year old Delta 14 and find it just fine, however I work on 2 tall ships and one has a 14" and an 18" Laguna, and the other has a 14" Laguna - all with 3 HP motors and you would be hard-pressed to find a better tool.

Ed
Ed M
Diane Kauffmds
Posts: 3246
Joined: Sun Mar 09, 2014 8:13 pm

Re: Band Saw - Bench top versus floor

Post by Diane Kauffmds »

I have a 10" Rikon, which has been a really good bandsaw for day to day work. But, if you have the room and the money, I would go ahead and get a good 14". Think to the future. I use the bandsaw more than any of the other tools in the shop.

Don't get me wrong. Given the position I was in a couple of years ago, I made a good decision buying the 10" Rikon, and it's a great bandsaw. But, I know that I'll be buying a 14" Rikon in the near future. Although rare, there have been a couple of instances where I've needed more power than the 10" could provide, and a good 14" has minimal resaw capability.
Diane Kauffmann
Country Roads Guitars
countryroadsguitars@gmail.com
PSmill
Posts: 111
Joined: Sun Sep 09, 2018 12:23 pm
Location: British Columbia, Canada

Re: Band Saw - Bench top versus floor

Post by PSmill »

Thanks for the advice!!
MaineGeezer
Posts: 1711
Joined: Wed Aug 13, 2014 12:14 pm

Re: Band Saw - Bench top versus floor

Post by MaineGeezer »

If you get a big one, I doubt you will ever wish you had gotten a small one. The reverse, however, may not be the case.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Post Reply