Brace Carving Jig
-
- Posts: 414
- Joined: Fri Jul 03, 2015 2:45 pm
- Contact:
Brace Carving Jig
I've been to Martin a couple of times and the last time I took a bunch of photos. I did not look at the photos for a couple years, but when I did I came across a photo of a woman carving braces that inspired me to make this jig. I had completely forgotten that I had seen it. It makes brace carving much easier. Using it, you don't have to hold the work to keep it from sliding. Many of you may already be using something similar, but I thought I'd share this because I really like it. The photos tell the story. Basically it is just a peg board that allows you to move the pegs at will. It will hold any shape in any position. The underside has a cleat that goes up against the edge of the bench to keep the peg board from sliding. I made mine with 3/4"plywood and 3/4" dowel pegs. Can't remember if I used a spade bit or a Forstner bit to drill the holes, but they both would work.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 13
- Joined: Thu Feb 16, 2017 10:05 pm
Re: Brace Carving Jig
nice tool. Wish I thought of it.
George
George
-
- Posts: 1715
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Brace Carving Jig
Does the board have a radius in it? Seems as though it should.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 3255
- Joined: Sun Mar 09, 2014 8:13 pm
Re: Brace Carving Jig
I like it. I think I'd add a foam rubber pad to accommodate back radiuses.
-
- Posts: 414
- Joined: Fri Jul 03, 2015 2:45 pm
- Contact:
Re: Brace Carving Jig
The radius does not matter. You are only carving on 1 brace at a time, pushing against the posts and turning the workpiece as needed. Radius is not a problem, and no padding needed.
-
- Posts: 7016
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: Brace Carving Jig
a foam pad may sound good but it is counter productive.
I did the same thing as Bob but now I use the rep fence on my table saw.
thanks BOB
I did the same thing as Bob but now I use the rep fence on my table saw.
thanks BOB
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 733
- Joined: Mon Jul 28, 2014 7:50 am
- Location: Chadds Ford, PA
Re: Brace Carving Jig
When I was up in Nazareth in December, the carving station was uncharacteristically empty giving a good look at the board. They were on a reduced work schedule.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 733
- Joined: Mon Jul 28, 2014 7:50 am
- Location: Chadds Ford, PA
Re: Brace Carving Jig
To Diane's comment, another pic from Nazareth showing use of backing material over the jig that is like Bob's in his original post.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 1715
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Brace Carving Jig
I think you would want something soft between the top and board to keep from scratching the top. It wouldn't have to be much, a piece of flannel cloth or something like that would do it.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion