Not quite a guitar tip-Just a shop tip.

Bright Ideas That Work? Tell Us!
Post Reply
Bob Gleason
Posts: 412
Joined: Fri Jul 03, 2015 2:45 pm
Contact:

Not quite a guitar tip-Just a shop tip.

Post by Bob Gleason »

Here is an idea that works for me on the bandsaw. Most of us use scrap wood as a backing on the table to create a zero throat when cutting thin pieces of wood. Anyone who does that knows that the backing has a tendency to run away, sometimes interfering with the cut in progress. The last photo is just such a runaway piece of backing.The cut in the backing also clogs with dust making it impossible to back it off the blade. No loss really, but it means you have to use new backing often. To keep the backing from sliding I cut a couple of strips of self adhesive sand paper, you could use regular sandpaper and spray adhesive, and apply it to the underside of my backing. 120 grit seems to work good, but I’m sure other grits would be fine too. It keeps the backing in place, and it usually can be backed off the blade for future use. The heavier work I’m doing, the heavier piece of backing I use. It varies from 1/4” ply to 5/8” ply, depending on the task at hand. Works for me. Enjoy your woodwork!—Bob G.
You do not have the required permissions to view the files attached to this post.
Danl8
Posts: 733
Joined: Mon Jul 28, 2014 7:50 am
Location: Chadds Ford, PA

Re: Not quite a guitar tip-Just a shop tip.

Post by Danl8 »

Nice idea, think I will give it a try.
tippie53
Posts: 7011
Joined: Fri Mar 03, 2006 7:09 pm
Location: Hegins, Pa
Contact:

Re: Not quite a guitar tip-Just a shop tip.

Post by tippie53 »

yes use that same trick
it makes cutting more accurate and safer
thanks BOB
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Kbore
Posts: 299
Joined: Sun Jun 25, 2017 3:58 pm
Location: St. Louis area

Re: Not quite a guitar tip-Just a shop tip.

Post by Kbore »

Thanks for the tip, I have never done that.

While on the bandsaw subject, who uses a blade lubricant and what kind? Went to a resaw workshop and the instructor used and recommended it (wood friendly). It was in a cardboard tube like a caulk cartridge.
Measure Twice,

Karl B
tippie53
Posts: 7011
Joined: Fri Mar 03, 2006 7:09 pm
Location: Hegins, Pa
Contact:

Re: Not quite a guitar tip-Just a shop tip.

Post by tippie53 »

I find them useless
Your saw teeth have a set. That means there is a clearance cut by the tooth and the side of the blade should be free. Bet that guy was selling the stuff .

Put me down for set up the saw right no need for blade lube.

I only cut a few 100 sets a year and that doesn't count the molds and plywood I run through . Learn to get the proper blade.

Good rule of thumb is to have 4 to 6 teeth in the work so if you have a 3/4 in blade a 6 tooth per inch

I also use different teeth
J hood raker etc. Find the teeth that work for you. I get my blades here
https://www.bandsawbladesdirect.com/
talk to the sales people they know the product and can get you the right blade. A good blade isn't cheap but it will out cut and out last the cheap blade and make the investment worth the $$$$.
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Kbore
Posts: 299
Joined: Sun Jun 25, 2017 3:58 pm
Location: St. Louis area

Re: Not quite a guitar tip-Just a shop tip.

Post by Kbore »

Bob Gleason wrote:... cut a couple of strips of self adhesive sand paper, you could use regular sandpaper and spray adhesive, and apply it to the underside of my backing.!—Bob G.
So,is the sandpaper touching your piece being sawn, sandwiched between the two wood pieces?
Measure Twice,

Karl B
Post Reply