spray booth
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: spray booth
Just set up the Fuji Semi Pro 2 sprayer. The turbine is loud so I mounted it outside the booth. The plug is inside. Will show the details soon. Made a small mixing counter. Was going to make a curing cabinet but I think the room vents easy enough and heats well. Will try some shelves with the floor VOC vent. I will keep you posted . I opened an account with
Mohawk and will try some other finishes. I have water borne Emtec 9003 and will soon try pre catalyzed varnish. I will keep you posted
Mohawk and will try some other finishes. I have water borne Emtec 9003 and will soon try pre catalyzed varnish. I will keep you posted
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: spray booth
booth is finished. I have a mixing area tool area containers and the resting bench. I am able to spray 3 guitars at one time
The turbine is outside the booth for noise control and the manufacture wants it 20 feet from the spray or wall separated. Kills 2 birds with one stone. I an pleased with the light and air flow. I have also added a small 30 pint dehumidfier and 600 btu ac unit.
they are in the main room.
The turbine is outside the booth for noise control and the manufacture wants it 20 feet from the spray or wall separated. Kills 2 birds with one stone. I an pleased with the light and air flow. I have also added a small 30 pint dehumidfier and 600 btu ac unit.
they are in the main room.
You do not have the required permissions to view the files attached to this post.
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 55
- Joined: Fri Jan 24, 2020 5:35 pm
Re: spray booth
What did you use for an exhaust fan?
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: spray booth
I have an 8 inch duct fan. I run that and I have2 smaller 4 in fans I run after I spray to expel the voc
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 191
- Joined: Fri Aug 28, 2009 8:58 am
- Location: Bethlehem, Pennsylvania
Re: spray booth
Great set up!! I'm very jealous.
Need a polisher?? ;-)
Need a polisher?? ;-)
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: spray booth
I started level sanding and buffing on the first guitar I sprayed in the booth.
Happy with the result .
After the initial spray I level sanded. Then I needed to add a few coats. So my process was like this
Mix ratio
60% lacquer ( mohawk )
thinner retarder mix 50 50 . that I blended to mix 60/40 and use a viscosity cup to know what
the viscosity is . Use the manufactures recommendations.
I am using a fuji semi pro 2 . So you may have to use something different for your gun. Experiment to find your
best result.
I allowed about 10 days cure time. You know your ok when you can sand and not get pilling up on the sand paper.
I have sanding blocks that I make from plywood and foam padding.
I start with 600 to get 1/2 way through the unevenness , then 800 1200 1500 then I use micro mesh 1500 2400 3600 and buff and polish with mazerna buffing paste and dommet and flannel wheels
Happy with the result .
After the initial spray I level sanded. Then I needed to add a few coats. So my process was like this
Mix ratio
60% lacquer ( mohawk )
thinner retarder mix 50 50 . that I blended to mix 60/40 and use a viscosity cup to know what
the viscosity is . Use the manufactures recommendations.
I am using a fuji semi pro 2 . So you may have to use something different for your gun. Experiment to find your
best result.
I allowed about 10 days cure time. You know your ok when you can sand and not get pilling up on the sand paper.
I have sanding blocks that I make from plywood and foam padding.
I start with 600 to get 1/2 way through the unevenness , then 800 1200 1500 then I use micro mesh 1500 2400 3600 and buff and polish with mazerna buffing paste and dommet and flannel wheels
You do not have the required permissions to view the files attached to this post.
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: spray booth
my black strat body is about done
You do not have the required permissions to view the files attached to this post.
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 3252
- Joined: Sun Mar 09, 2014 8:13 pm
Re: spray booth
John, which gun would you recommend for an existing compressor? I have a 20 gal. porter cable (link below for specs).
CFM @ 40 PSI = 6.2
CFM @ 90 PSI = 5.3
https://www.tractorsupply.com/tsc/produ ... compressor
CFM @ 40 PSI = 6.2
CFM @ 90 PSI = 5.3
https://www.tractorsupply.com/tsc/produ ... compressor
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: spray booth
I suggest a good water separator
get a decent hvlp gun
I have one from HF that actually does a great job this one has different nozzles and needles for different material
https://www.amazon.com/4YANG-Gravity-Sp ... 71&sr=8-28
get a decent hvlp gun
I have one from HF that actually does a great job this one has different nozzles and needles for different material
https://www.amazon.com/4YANG-Gravity-Sp ... 71&sr=8-28
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 3252
- Joined: Sun Mar 09, 2014 8:13 pm
Re: spray booth
You told me about the water separator, so Frank put a good one on the compressor. I also have a valve to drain it easily, which I do daily when I turn it off. I thank you for the information. This is the compressor you recommended a few years ago, and it's been a very good compressor.
Thanks for the spray gun information. I've put it in my Amazon cart!
Thanks for the spray gun information. I've put it in my Amazon cart!