www.KitGuitarsForum.com

Learn to Kit Build a Guitar. Learn to Scratch Build a Guitar. Learn EVERYTHING Guitars Here!
It is currently Wed Jul 17, 2019 3:29 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Sun Mar 10, 2019 1:05 am 
Offline

Joined: Sun Sep 08, 2013 11:39 pm
Posts: 137
My first two builds were OM-type guitars built following plans in Jonathan Kinkead's book, but I modified them with 12 fret necks, and altered bracing, bridge, and soundhole. I'm very happy with them, and am still tweaking the setup on both. Number 3 is a "straight" Kinkead OM copy, bearclaw B.C. Engelmann top with a nice tap, and black walnut back, sides, heelblock and neck, with pretty but undramatic (and less-challenging) grain. The plates and bracing are a little lighter than Kinkead's somewhat heavy specs. I fitted a herringbone rosette that I think is widely available, but I got mine at Lee Valley. I will use prebent herringbone purfling from Bow River Woods (easier for me to deal with Canadian suppliers), Indian ebony bridge, fingerboard, and headplate, aiming for a bit of a black-and-white look, looking for good quality black tuning machines to finish it off. The kerfing was new to me, from Bow River, mahogany apparently glued to a veneer of perhaps maple, which was very flexible and nice to work with. This is actually only my second "build", as the first two were built concurrently. I'm enjoying having some of the steps more familiar, some of the jigs already made, and doing a better job after some experience.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Sun Mar 10, 2019 11:38 am 
Offline

Joined: Sat Nov 13, 2010 9:55 pm
Posts: 506
Location: Pittsburgh PA suburbs
Very cool, I'm doing something very similar but not as far along. I'll be following this thread now in many ways LOL. Good luck!

_________________
~ Neil


Top
 Profile  
 
PostPosted: Sun Mar 10, 2019 2:59 pm 
Offline

Joined: Sun Mar 09, 2014 8:13 pm
Posts: 1874
It's great that your growing and learning. I've done that same thing and I learn with each subsequent build. It get's very interesting when you start designing your builds. Your build looks great.


Top
 Profile  
 
PostPosted: Wed Mar 20, 2019 7:38 pm 
Offline

Joined: Thu Feb 21, 2019 10:51 am
Posts: 36
Location: Fishers, IN
Very curious about the walnut back and sides. I can't swing a cat without hitting black walnut lumber (Indiana, who knew?), sounds like a good tone wood from the little bit of research I've done, internet says its between rosewood and mahogany, but curious to get feedback from others? Would be a relatively inexpensive material for me to learn on - thanks!

_________________
"Facts seldom sway an opinion." - John Hall
"The difference between theory and practice is that in theory there is no difference." - van de Snepscheut


Top
 Profile  
 
PostPosted: Mon Mar 25, 2019 9:55 am 
Offline

Joined: Sun Mar 09, 2014 8:13 pm
Posts: 1874
WV is FULL of black walnut. It's a great Tonewood. I've bought a bunch of old stock from our local lumberyard. Even though some pieces are 2" thick you can hear them ring when you tap them, or bonk them on the floor. My first guitar, which I sold, was walnut. It's got a nicely rounded voice with nice bass. I built an OM.

If i were to compare it to mahogany or EIR, I'd place it more toward the hog, with a bit more clarity in the mids and trebles.


Top
 Profile  
 
PostPosted: Sun Apr 07, 2019 11:24 pm 
Offline

Joined: Sun Sep 08, 2013 11:39 pm
Posts: 137
I got the top and back glued to the sides okay on this, but ran into problems with bindings. I got some walnut binding pieces which happened to be large enough to mill four strips from each, about 3/32 x 1/4" after sanding. But it was a nightmare to bend. I broke one piece just sanding it. Then I broke several (laminated with WBW purfling) on my underpowered bending iron. I have bent three sets of sides (walnut, cherry, and rosewood), and rosewood and maple bindings with this, albeit with some difficulty. I prepared a new set of laminated bindings and took them, plus a set of unlaminated bindings, in case I broke a few, to a friend's shop to use his side bender with silicon blanket, which has bent many sides successfully. We set it up, sprayed the wood, wrapped it in parchment (his recommendation) and put it in the bender at 275F (this is maybe a little low but is still hotter than I have been able to get my bender at home, but still managed to bend walnut sides). Results in photo following, with the breaks mostly pretty straight across the grain. I know this sort of thing can happen, and maybe it was bad wood, but still disheartening, mostly because you don't know what went wrong. So I will order some more and try again, and hope to learn what might have been the problem. While I wait for material, I am gluing up the walnut neck. Two steps forward, one step back . . .


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Sun Apr 07, 2019 11:35 pm 
Offline

Joined: Mon Jul 09, 2012 9:49 pm
Posts: 227
In my limited experience, I've noticed that runout and bending don't play well together. Especially noticed in bindings.

_________________
peter havriluk


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group