www.KitGuitarsForum.com

Learn to Kit Build a Guitar. Learn to Scratch Build a Guitar. Learn EVERYTHING Guitars Here!
It is currently Fri Dec 15, 2017 12:11 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 18 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: Fri Jun 16, 2017 9:03 pm 
Offline

Joined: Sun Mar 09, 2014 8:13 pm
Posts: 1313
Love the spokeshave.


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 12:37 pm 
Offline

Joined: Sat Feb 09, 2008 8:06 pm
Posts: 2925
Location: Visalia, CA
Here is where I am thus far. The neck is done and fit to the body, frets installed and recrowned, etc. I have done some gap filling, need to go over it again, then I will be ready to begin porefilling. I think I will use Zpoxy on the Sapele. I've used Timbermate rosewood color in the past and that turned out well, but want to try the Zpoxy for the first time, so that is what I'll use. The walnut binding I probably will just let the lacquer fill, I'll Zpoxy the headstock too. I have filled the walnut rosette with CA. The neck is also Sapele and I may use shellac and sawdust to pore fill there...might work better than Zpoxy would on the curved areas?
I will either make a walnut or ebony bridge. I have some pretty cool burly olive I may use for a pickguard.
I plan to put up the spray booth and be spraying early September, probably start the weekend of Labor Day. Then the guitar can sit and cure until I return from India in mid November. That should work out well.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 12:38 pm 
Offline

Joined: Sat Feb 09, 2008 8:06 pm
Posts: 2925
Location: Visalia, CA
couple more pics


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Thu Aug 10, 2017 2:53 pm 
Offline

Joined: Sat Feb 09, 2008 8:06 pm
Posts: 2925
Location: Visalia, CA
Well I now have this one all pore filled and sanded. All I need to do before I start spraying the Nitro on Labor Day weekend is mask it off.
I'll post again on it then.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Tue Sep 05, 2017 12:18 pm 
Offline

Joined: Sat Feb 09, 2008 8:06 pm
Posts: 2925
Location: Visalia, CA
This guitar has been in the spray booth for a week. I put the last 3 coats on yesterday morning.
Now it will hang for about two months while we take our trip to India. The nitro lacquer went on nicely this time.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Tue Sep 05, 2017 9:00 pm 
Offline

Joined: Sun Jun 25, 2017 3:58 pm
Posts: 189
Location: St. Louis area
Cant wait to see that wood under the finish. Very very nice job. Don't you love it when a plan comes together!

_________________
Measure Twice,

Karl B


Top
 Profile  
 
PostPosted: Thu Nov 16, 2017 12:22 pm 
Offline

Joined: Sat Feb 09, 2008 8:06 pm
Posts: 2925
Location: Visalia, CA
Well I am back from India, and this guitar has cured for almost 10 weeks, so I've started flatsanding the lacquer. That is going well. Starting out with 800 git.
I had a little mishap that gladly will not show. The handle I put into the mortise on the body for spraying/hanging was a very close fit. The lacquer bridged the space between the handle and the mortise. I cut through the lacquer all the way around with an exacto knife ( or thought I did) before pulling that handle out,.....but.....one area was not cut loose and pulled, not only lacquer but some wood up with it....stupid on my part for sure. Luckily the neck heel will cover this area, so I'm not fretting much about it. I did weep some CA in so the area is secure.
Just another learning experience...patience, and paying closer attention to details learned.

I should be a nice looking guitar. I'm hoping the action holds up okay once it gets to India. In the future I'm going to built the India guitars with an extension off the the neck block so that area does not sink in. Two of my guitars have done this to some degree after time spent in India.

I will post some pics when I'm to the polishing stage.


Top
 Profile  
 
PostPosted: Thu Nov 16, 2017 9:59 pm 
Offline

Joined: Sun Mar 09, 2014 8:13 pm
Posts: 1313
It's a beautiful guitar Kevin.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 18 posts ]  Go to page Previous  1, 2

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group