Guitar #3 -- an OM cutaway
-
- Posts: 3730
- Joined: Sat Feb 09, 2008 8:06 pm
- Location: Visalia, CA
Re: Guitar #3 -- an OM cutaway
Gorgeous wood there!
-
- Posts: 1719
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Guitar #3 -- an OM cutaway
I got it from Tom Thiel in Center Sandwich, NH. Iit looks even better now, with more finish on it. I hope I can do it justice.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 1719
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Guitar #3 -- an OM cutaway
I got the kerfing glued on the top edges of the sides and sanded to a 25' radius. Next step will be to put on the side braces.
You do not have the required permissions to view the files attached to this post.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 296
- Joined: Wed Nov 26, 2014 7:52 pm
- Location: Saint Paul, MN
Re: Guitar #3 -- an OM cutaway
Looking good. I tend to glue the side braces before top or back goes on for ease of clamping.
Learning every day.
-
- Posts: 1719
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Guitar #3 -- an OM cutaway
Good thought. That would be the logical sequence.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 1719
- Joined: Wed Aug 13, 2014 12:14 pm
Gluing in the tail wedge
This should have been done before I glued the back, too.
You do not have the required permissions to view the files attached to this post.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 296
- Joined: Wed Nov 26, 2014 7:52 pm
- Location: Saint Paul, MN
Re: Guitar #3 -- an OM cutaway
Live and learn. This weekend I glued in the x braces before routing and installing the rosette. Made for a challenge ;-)
Learning every day.
-
- Posts: 1719
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Guitar #3 -- an OM cutaway
Yes, that would make life more difficult than it really needs to be!
The wedge came out quite nicely. The hole for the end pin (it will be a pickup jack, hence the 1/2" hole) is centered and everything. I began to think things were going well. I should never do that! I then proceeded to mangle the notch in the X brace. I need to get a couple more strips and try again.
The wedge came out quite nicely. The hole for the end pin (it will be a pickup jack, hence the 1/2" hole) is centered and everything. I began to think things were going well. I should never do that! I then proceeded to mangle the notch in the X brace. I need to get a couple more strips and try again.
You do not have the required permissions to view the files attached to this post.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 296
- Joined: Wed Nov 26, 2014 7:52 pm
- Location: Saint Paul, MN
Re: Guitar #3 -- an OM cutaway
I like the contrast of the dark wedge against the lighter sides.
Learning every day.
-
- Posts: 1719
- Joined: Wed Aug 13, 2014 12:14 pm
Gluing on the top braces
Those of you in snow country will undoubtedly recognize the rods I'm using as go-bar rods. (Maybe they are available in non-snow areas too.) If you're unfamiliar with them, they're fiberglass rods about 4' long used to mark the edges of driveways, sidewalks, and such. They are pretty cheap -- $2 or so apiece -- and work well as go-bar rods. They happen to be just the right length to fit between my bench top and the ceiling.
The wood strips I'm also using are hickory.
The wood strips I'm also using are hickory.
You do not have the required permissions to view the files attached to this post.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion