Page 9 of 10

Re: 1st build; time to stop dillydallying!

Posted: Fri Jan 08, 2021 9:28 am
by RHayes
That setup should work well for you. I have yet to do anything beyond a simple binding channel so looking forward to your progress.

Re: 1st build; time to stop dillydallying!

Posted: Fri Jan 08, 2021 10:52 am
by ruby@magpage.com
Is that $50 worth of hooks? Looks like it will work, but love to see it in action

Re: 1st build; time to stop dillydallying!

Posted: Fri Jan 08, 2021 3:52 pm
by BEJ
Forgot how much they cost, did take them off the old set up though. Will get some pics of the binding process as it proceeds.

Bruce,

Re: 1st build; time to stop dillydallying!

Posted: Mon Jan 25, 2021 12:31 am
by BEJ
Some more progress, these 2 with bindings installed, binding must be the thing I hate the most building these things. Both have a 1st coat of Z poxie for some protection, seems like I have banged up past builds with little nicks and scratches.

Bruce,

Re: 1st build; time to stop dillydallying!

Posted: Sat Feb 13, 2021 3:13 am
by BEJ
Got some more work done on the bindings. Seems like no matter what I try I get small gaps at various points. Thought I would try this to clean these gaps and make room for some accents.

I used a 1/8" Dremel st bit to cut a channel that would take 7 veneer strips. I found some birch and walnut veneer packs at Woodcraft and cut a bunch of them for this and rosettes. I cut have cut a smaller inner rabbitt when I did the binding channel but still would have had gaps.

Cutting a channel this way you have to keep the guide rod always tight against the guitar body and any outward movement will muck it up. Had to sand the channel a little in a few places but overall it went well. Centering the bit on the gap seemed to leave a clean channel. Maybe a little too wide but this is a practice guitar for now, trying out new things. A few pics....

Bruce,
binding cuts19852016.JPG
binding cuts19852016.JPG
binding cuts19852013.JPG

Re: 1st build; time to stop dillydallying!

Posted: Sat Feb 13, 2021 3:16 am
by BEJ
A few pics of the dremel set up a dimmer switch to lower speed....
binding cuts19852021.JPG
binding cuts19852020.JPG

Re: 1st build; time to stop dillydallying!

Posted: Thu Mar 25, 2021 11:24 pm
by BEJ
Still chugging along, started finishing these 3, a little rough now but looking better after a few more coats....

Re: 1st build; time to stop dillydallying!

Posted: Tue Oct 11, 2022 7:30 pm
by BEJ
Been awhile since I've posted on this thread. Still at it, have finished the above 3 and will post some pics.

Went by Crosscut Hardwoods/Seattle a few weeks ago they had some nice new additions, one being some real nice Cypress not full q sawn but close enough. Started on 3 new builds with this wood, maybe "The 3 Blondes" should be a different look. A few pics...

Re: 1st build; time to stop dillydallying!

Posted: Thu Oct 13, 2022 9:55 pm
by BEJ
Got some more done today, almost have the 3 boxes ready for binding, not sure if binding or fretting is the job I hate the most, a toss up at best. A few pics...

Bruce,

Re: 1st build; time to stop dillydallying!

Posted: Thu Oct 13, 2022 11:24 pm
by Stray Feathers
You're making lots of instruments! I'm interested to hear how your most recent guitars, with the symmetrical X-bracing, sound compared to your earlier ones. I too have made several now following Kinkead for the most part, and a Kinkead-body 12-string but with symmetrical X-bracing, which sounds great. I'm just starting a couple more six-string OMs (probably) and may try some things your way. Bruce W.