Came across this YT Video where the builder utilizes a table to aid the side bending process with using an Iron. For me, whose not quite proficient enough with an iron found it to be a useful item to keep the sides 90 degrees to the iron. I like his old school method of building.
https://www.youtube.com/watch?v=qvsDcM0HaqU
Work Table for Bending Iron
-
- Posts: 210
- Joined: Wed Jan 25, 2012 1:44 pm
- Location: Bay Area
-
- Posts: 299
- Joined: Sun Jun 25, 2017 3:58 pm
- Location: St. Louis area
Re: Work Table for Bending Iron
Thanks for posting that video, fantastic watching a craftsman work.
Measure Twice,
Karl B
Karl B
-
- Posts: 3256
- Joined: Sun Mar 09, 2014 8:13 pm
Re: Work Table for Bending Iron
He's using an iron that looks almost identical to mine. The table is a great idea. Thanks for posting.
-
- Posts: 7016
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: Work Table for Bending Iron
I tried a table and I never had any luck with it.
Here is one trick I did learn when I was hand bending
you need 2 things a pull slat you can take a piece of aluminum or stainless that is flxible and help sandwich tighter curves
A steam iron
When you are dealing with high figure woods there is a high degree of cracking because of the run out of the wood that gives it that distinct pattern Using a slat you can "PRESS" the wood with more control. The cracking comes from flexing it over the iron.
On high figure I used the steam iron with the bendind iron and with that I could steam the wood and heat on both side at the waist to get a higher degree of success in bending. It didn't take me long to realize the bending machine was more efficient . I can bend in less than 5 min but again I am doing a bit more . I bend just about daily .
Never be afraid to experiment. Find what works for you as there is always another way that works
Here is one trick I did learn when I was hand bending
you need 2 things a pull slat you can take a piece of aluminum or stainless that is flxible and help sandwich tighter curves
A steam iron
When you are dealing with high figure woods there is a high degree of cracking because of the run out of the wood that gives it that distinct pattern Using a slat you can "PRESS" the wood with more control. The cracking comes from flexing it over the iron.
On high figure I used the steam iron with the bendind iron and with that I could steam the wood and heat on both side at the waist to get a higher degree of success in bending. It didn't take me long to realize the bending machine was more efficient . I can bend in less than 5 min but again I am doing a bit more . I bend just about daily .
Never be afraid to experiment. Find what works for you as there is always another way that works
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 210
- Joined: Wed Jan 25, 2012 1:44 pm
- Location: Bay Area
Re: Work Table for Bending Iron
tippie53 wrote:Never be afraid to experiment.
I did make my own table. I thought it would be advantageous to this novice bender. Basically copied it from the video above.
As a trial bend on Australian Blkwood that's the intended B&S wood I chose for this build, I used the cutoffs' from the back pieces to get an idea how well it would bend. It bent fairly easy & all went well even though the depth was way off...
Figuring that the trial bend went w/o issue, I thought I'd go ahead & bend the sides for the SJ. I had thicknessed the sides down to .075", whereas the trial pieces were about .090". I didn't get very far on the waist bend when I started to feel a crack develop. After that, it was all downhill! Cracked the waist in 4 spots. A failed attempt...sigh! I should've been more careful w/ this flamey wood. Not sure if it can be saved?
-
- Posts: 7016
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: Work Table for Bending Iron
this can be repairable
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com