Birdseye Maple
-
- Posts: 3719
- Joined: Sat Feb 09, 2008 8:06 pm
- Location: Visalia, CA
Birdseye Maple
My local wood vendor has a beautiful 8/4 billet of birdseye maple, and when I was there last Saturday I neglected to see if it was quarter sawn. My understanding is if the birdseyes are showing, it will NOT be quarter sawn.
My question is how well will this work for acoustic back and sides? I know quarter sawn is preferred. I've not bent any maple yet, although I have a set of ambrosia maple that I don't think is quartered either.
My question is how well will this work for acoustic back and sides? I know quarter sawn is preferred. I've not bent any maple yet, although I have a set of ambrosia maple that I don't think is quartered either.
-
- Posts: 1715
- Joined: Wed Aug 13, 2014 12:14 pm
Re: Birdseye Maple
People with more knowledge than I have may correct me, but I think quartersawn is important only in the top and braces. For sides and back, appearance takes precedence and whatever cut produces good-looking grain is fine.
Don't believe everything you know.
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
Anything is possible if you don't know what you are talking about.
When things are bad, try not to make them any worse, because it is quite likely they are bad enough already. - French Foreign Legion
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: Birdseye Maple
Yes Maple will work both ways . I have used it many times.
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 3719
- Joined: Sat Feb 09, 2008 8:06 pm
- Location: Visalia, CA
Re: Birdseye Maple
John, any problems bending it?
-
- Posts: 7013
- Joined: Fri Mar 03, 2006 7:09 pm
- Location: Hegins, Pa
- Contact:
Re: Birdseye Maple
maple likes just s mist of water and heat so bend 275 to 350
John Hall
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
Blues Creek Guitars Inc
Authorized CF Martin Repair Center
president of Association of Stringed Instrument Artisans
http://www.bluescreekguitars.com
-
- Posts: 3252
- Joined: Sun Mar 09, 2014 8:13 pm
Re: Birdseye Maple
That's good to know about the maple. The cherry that I used in my 00 came from a local lumber company. It has a grain that is totally wild. All of the billets are flat sawn and I had no problems with bending. It turned out so well that I went back and got more; they're sitting on a shelf in the basement.
viewtopic.php?f=7&t=7551
viewtopic.php?f=7&t=7551
-
- Posts: 3719
- Joined: Sat Feb 09, 2008 8:06 pm
- Location: Visalia, CA
Re: Birdseye Maple
Good to know, thank you. I think I'm going to get that billet if he has it when I'm able to make a short trip again the the wood store.
-
- Posts: 3719
- Joined: Sat Feb 09, 2008 8:06 pm
- Location: Visalia, CA
Re: Birdseye Maple
John, one more question. Do you think I'll have any trouble resawing this billet of maple? I have a Woodslicer blade and have been successful resawing a billet of Sapele.
-
- Posts: 733
- Joined: Mon Jul 28, 2014 7:50 am
- Location: Chadds Ford, PA
Re: Birdseye Maple
I'm just finishing up a birdseye cutaway. Best figure is flatsawn (I believe -- at least all of mine is) which can get squirrely. This one has a flat spot on the treble side, but I can live with it. I've had eyes pop out in the past when planed or chiseled or during band sawing (goes better with really sharp blades and a narrower set).
You do not have the required permissions to view the files attached to this post.
-
- Posts: 3719
- Joined: Sat Feb 09, 2008 8:06 pm
- Location: Visalia, CA
Re: Birdseye Maple
Looks very nice Dan, what is the binding?